The Paper Puzzle Parade
Build your own paper rocket |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Hi there!
Still looking for something to shoot into the sky on new year eve?
Here it is: Using pressurized air as it's only fuel, the rocket might rise as high as five meters. No fire and no explosives are used - it's perfectly safe for indoor use. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The rocket kit
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
How to build the rocket :Building the rocket is rated "tricky". Folding the bellow requieres some endurance. The most important thing to observe is that all bellow parts must be air tight! The more precise you work, the higher the rocket will fly.
The most difficult part is the bellow's side wall. Cut it out and carefully scribe the bending lines! Then strictly follow the bending lines:
Outside bend line as described in detail on the Tools and Tips page. The bends must not break! If they do, close the slits with adhesive tape, applied to the back side of the paper. The folded bellow is then glued to the base plate. Remember: The connection ought to be air tight! Fold up the flaps at the front of the base plate and glue them to the top side of the folded bellow.
Build the starting tube by coiling the part around a pen or a stick. Slide it up through the top plate as shown on the left and glue it on the back (bottom) side of the top plate. After the glue of the first connections has dried, mount the top plate on top of the bellow. Check whether everything is air tight: Close the end of the starting tube with your finger and carefully press the bellow. If you find any escapes for the air, stop them up! Now build the rocket itself. Once again, the tubular part should be prepared by winding the paper around a stick or a pen. The finished tube must fit over the starting tube and slide easily along it. Form a cone as the rocket tip and glue it on top of the tube - once
again: Air tight, please ... Wait some minutes to allow the glue to dry.
Now you're ready for the first take off:
Watch the rocket race into the sky - or most likely into your room's ceiling ... If you did a good work with the bellow, five meters of height should be no problem. If you have built the rocket - why not leave a comment in my guestbook? |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
New:
Send in your flight data!
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Flight data sent in
until now:
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Tips
and tricks sent in by other rocket pilots:
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
If you like this page, why don't you add something to my guestbook? | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
This kit: © 1997, 98 by Georg Eggers, all rigths reserved. Not to be used for any commercial purpose!
Last modifications: Wednesday, January 04, 2001
Author: Georg Eggers email:
Please leave a comment in the Guestbook!